Futura BIO - Cht-cichewicz - Boilers, biomass heating, pellets bolier

Futura BIO - Boilers
Biomass boilers with automatic feeding
Futura BIO

News

www.cichewicz.com / Boilers / Biomass boilers with automatic feeding / Futura BIO

Futura Bio

If we would like to burn grain or bigger pellets, we reccomend to use our new ceramics burner head.

Equipment of boiler

Futura Bio is steel water boiler which burns wood and corn pellets, wood chips, pure wood rubbish. These are renewable ,environmentally friendly, very cheap and easy to buy domestic fuels which can replace imported, more expensive liquid fuel like gas and oil.

Futura Bio heating system contains :
-3 pass boiler made from steel (5-8 mm )
-Outer Jacket with insulation
-Fuel tank with capacity 1 – 6 m ³
-Worm Conveyor and Gearbox NORD
-Blower
-Turbulators
-Ceramic Insert
-Digital boiler control
-Pressure Tank set for automatic burn-back protection
-Overheat Cooling Coil

FUNCTIONS AND FEATURES OF FUTURA PIRO

Solid quality
Heater and flue gas plates made from steel 5-8 mm thick (depend on kW version) , combustion chamber made from iron coast and ceramic. Boiler is welded by robots and obligatory pressure controlled

Digital steering
The Electronic Control Unit regulates the flow of fuel and air for combustion and provides digital readings of boiler temperature, return temperature, and smoke temperature.

Combustion chamber
Behind the lowest door, the combustion chamber with the ceramic combustion zone can be seen. There is plenty of room for easy cleaning and ash removal. 3 pass water heater zone, provide heating efficiency of 84-88 % !
When iron coast parts are installed in chamber, we can deinstall hopper and burn solid fuel like: wood or coal.

Fuel tank 1,3 – 6 m³
Easy-to-load hopper with reversible door. The hopper can be loaded from either the back, right, or left side. Depend on capacity of the boiler , we have different volume of the fuel tank: f.e: 20 kW = 1,3 m³,
200 kW= 6 m³. For extra cost we can provide individual hopper volume to each boiler.

Gear motor and automatic feeding system of the fuel
The gear motor turns the worm conveyor/auger and feeds the fuel into the combustion chamber at the proper rate.. The system provides automatically fuel to the combustion chamber. User has to manually ignite the burner and add every 3-4 day fuel to the tank.

Requirement of the boiler

Requirement of the boiler

We need at least 4 up to 8 q m of the basement area
Because of the very high efficiency of the Multi-Heat boilers the flue gas exhaust temperatures can be low enough to cause condensation in the chimney. This condensation may, over time, damage a masonry chimney. If you have condensation in your chimney, a stainless steel chimney liner should be installed inside the flue
The chimney must be in good condition. Minimum size of the chimney is 20 cm x 20 cm No other appliance should be connected to this flue. Consult your local building inspector for the chimney requirements and install the boiler in accordance with all applicable codes.
Minimum heating area of the 20 kW boiler is 120 q m, maximum 200 kW boiler is 2 000 q m.

Technical Data

Output power (capacity)	A high	B width (boiler)	C depth	D	E	F	B width (tank)	Water capacity (l)	Suggested tank	Weight (kg)	Pressure (test)	Pressure (work)
25 kW	1450	646	700	1300	740	2500	700	60	30	350 kg	4,5 bar	2,5 bar
50 kW	1550	665	750	1550	740	2500	700	120	60	450 kg	4,5 bar	3 bar
72 kW	1510	870	1360	1550	740	2500	1500	285	110	960	4,5 bar	3 bar
105 kW	1680	880	1500	1550	740	2500	1500	356	200	1160	4,5 bar	3 bar
160 kW	1890	880	1640	1850	740	2500	2400	463	300	1390	4,5 bar	3 bar
245 kW	2000	1100	2430	1850	740	2500	2400	847	500	2500	4,5 bar	3 bar
325 kW	Special order